HomeProductsMotor Control ICsStepper Motor Controller IC

12x Low-Side for 3 Stepper Motors | E520.02 (*Driver IC)

The Elmos Stepper Motor control ICs increase efficiency and give you full control over the application. Furthermore Elmos offers unique features like stall detection: During the operation of a stepper motor, characteristic current and voltage profiles occur with each succeeding step, allowing a conclusion about the motor’s operating status. By recording and analyzing these signals, sensorless detection of a motor stall is possible. Elmos has the competence to integrate this function into ICs.
Part-No. / Function Interface Output VSUPPLY IPEAK P(Motor) peak RDSON Package Comment
E520.01 (*Driver IC)
12x Low-Side for 3 Stepper Motors with Stall Detection
  • SPI-compatible (3.3/5V)

12 channel

3V to 25V (42V)

≈12x 8.75W

1.5Ω

QFN32L5
  • Stall detection for stepper motors (E520.01) suitable for Full Step, Half Step, Wave Drive
  • 245Hz LED mode
  • 25kHz relay mode
  • 25kHz linear PWM
  • TJunc peak = +150°C
E520.02 (*Driver IC)
12x Low-Side for 3 Stepper Motors
  • SPI-compatible (3.3/5V)

12 channel

3V to 25V (42V)

≈12x 8.75W

1.5Ω

QFN32L5
 
  • 245Hz LED mode
  • 25kHz relay mode
  • 25kHz linear PWM
  • TJunc peak = +150°C
E520.03 (*Driver IC)
8x Low-Side for 2 Stepper Motors with Stall Detection
  • SPI-compatible (3.3/5V)

8 channel

3V to 25V (42V)

≈8x 8.75W

1.5Ω

QFN32L5
SOIC20
  • Stall detection for stepper motors suitable for Full Step, Half Step, Wave Drive
  • 245Hz LED mode
  • 25kHz relay mode
  • 25kHz linear PWM
  • TJunc peak = +150°C
E523.30 (*SoC)
Power Stepper Controller with Stall Detection and Auto Addressing (LIN/PWM Interface)
  • LIN 2.x (1.3 comp.) or
    SAE-J2602 or
    PWM Interface
  • Optional LIN Auto-Addressing (SNPD)
    only E523.30 or LIN Flash update
  • JTAG

2 channel

5.5V to 20V (42V)

≈ 25W

550mΩ(HS)
450mΩ(LS)

QFN32L6
  • Current chopper motor control
  • Supply and read-out of up to 3 sensors
  • Embedded 8bit µC
  • 8k FLASH
  • TJunc peak = +170°C
E523.39 (*Plug & Play)
SPI Stepper Driver
  • SPI-compatible (3.3/5V)

2 channel

5V to 28V (42V)

40W

0.5Ω (HS)
0.5Ω (LS)

QFN20L5
QFN32L6
 
  • Stall-Detection / analysis / position correction
  • Sensitive Fail-Current-Detection
  • Over modulation with customized waveforms
  • Supporting Adaptive-Holding-Torque
  • Supporting Adaptive-Run-Current
  • TJunc peak = +170°C
E523.62 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD

  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 600mA/ch

≈9W

1.6Ω (HS)
3.0Ω (LS)

TSSOP16-EP
  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 
E523.63 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD

  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 1000mA/ch

≈15W

0,6Ω (HS)
1,0Ω (LS)

TSSOP16-EP
  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 
*Plug & Play Chip with defined functionality | no controller programming necessary
*SoC System-on-a-Chip | with integrated microcontroller
*SBC System-Basic-Chip | with Voltage Regulator Reset, Watchdog, physical Interface
*Driver IC Driver Chip without SBC or SoC features
Show cookie popup