HomeApplikationenAutomotiveBody & ConvenienceHVAC SystemHVAC Flaps

Power Stepper Controller with Stall Detection and Auto Addressing (LIN/PWM Interface) | E523.30 (*SoC)

Motor Control Stepper Motor

Part-No. / Function Interface Output VSUPPLY IPEAK P(Motor) peak RDSON Package Comment
E520.01 (*Driver IC)
12x Low-Side for 3 Stepper Motors with Stall Detection
  • SPI-compatible (3.3/5V)

12 channel

3V to 25V (42V)

≈12x 8.75W

1.5Ω

QFN32L5
  • Stall detection for stepper motors (E520.01) suitable for Full Step, Half Step, Wave Drive
  • 245Hz LED mode
  • 25kHz relay mode
  • 25kHz linear PWM
  • TJunc peak = +150°C
E520.02 (*Driver IC)
12x Low-Side for 3 Stepper Motors
  • SPI-compatible (3.3/5V)

12 channel

3V to 25V (42V)

≈12x 8.75W

1.5Ω

QFN32L5
 
  • 245Hz LED mode
  • 25kHz relay mode
  • 25kHz linear PWM
  • TJunc peak = +150°C
E520.03 (*Driver IC)
8x Low-Side for 2 Stepper Motors with Stall Detection
  • SPI-compatible (3.3/5V)

8 channel

3V to 25V (42V)

≈8x 8.75W

1.5Ω

QFN32L5
SOIC20
  • Stall detection for stepper motors suitable for Full Step, Half Step, Wave Drive
  • 245Hz LED mode
  • 25kHz relay mode
  • 25kHz linear PWM
  • TJunc peak = +150°C
E523.30 (*SoC)
Power Stepper Controller with Stall Detection and Auto Addressing (LIN/PWM Interface)
  • LIN 2.x (1.3 comp.) or
    SAE-J2602 or
    PWM Interface
  • Optional LIN Auto-Addressing (SNPD)
    only E523.30 or LIN Flash update
  • JTAG

2 channel

5.5V to 20V (42V)

≈ 25W

550mΩ(HS)
450mΩ(LS)

QFN32L6
  • Current chopper motor control
  • Supply and read-out of up to 3 sensors
  • Embedded 8bit µC
  • 8k FLASH
  • TJunc peak = +170°C
E523.39 (*Plug & Play)
SPI Stepper Driver
  • SPI-compatible (3.3/5V)

2 channel

5V to 28V (42V)

40W

0.5Ω (HS)
0.5Ω (LS)

QFN20L5
QFN32L6
 
  • Stall-Detection / analysis / position correction
  • Sensitive Fail-Current-Detection
  • Over modulation with customized waveforms
  • Supporting Adaptive-Holding-Torque
  • Supporting Adaptive-Run-Current
  • TJunc peak = +170°C
E523.62 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD

  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 600mA/ch

≈9W

1.6Ω (HS)
3.0Ω (LS)

TSSOP16-EP
  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 
E523.63 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD

  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 1000mA/ch

≈15W

0,6Ω (HS)
1,0Ω (LS)

TSSOP16-EP
  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 

BLDC Motor BLDC Motor Driver

Part-No. / Function Interface VSUPPLY IPEAK P(Motor) peak RDSON Package Comment
E523.01 (*SBC)
B6 Bridge FET Driver (LIN/PWM Interface)
  • LIN 2.x (1.3 comp.),
    SAE-J2602(only E523.01) or
  • PWM bidirectional
  • LIN Flash update

7V to 28V (5V to 42V)

6 channel

≈1.5kW (external FETs)
≈3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN44L7
QSOP44
  • Voltage Regulator (3.3V/5V) selectable
  • Precise deadtime generation
  • Watchdog/Diagnostics
  • TJunc peak = +170°C
  • Demo software on request (sensorless sinus)
E523.10 (*SoC)
BLDC-Motor Driver with Cold-Crank Capability
  • PWM bidirectional
  • SPI for configuration

7V to 28V (4.5V to 42V)

6 channel

≈1.5kW (external FETs)
≈3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN44L7
  • Voltage Regulator (3.3V/5V) selectable
  • Precise deadtime generation
  • Watchdog/Diagnostics
  • TJunc peak = +170°C

Motor Control DC Motor

Part-No. / Function Interface VSUPPLY IPEAK P(Motor) max RDSON Package Comment
E523.05 (*SoC / *Plug & Play)
DC 2x Half-Bridge Controller with 16bit CPU (LIN / PWM Interface)
  • LIN 2.x (1.3 comp.),
    SAE-J2602 or
    PWM bidirectional
  • SPI for configuration
  • LIN Flash update
  • JTAG

7V to 28V (5V to 42V)

6 channel

≈1.5kW
(external FETs)

≈3W
(direct drive)

8Ω (HS)
4Ω (LS)

QFN48L7
  • 16bit/48 MHzCPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack software update via LIN
  • Charge Pump Driver included
  • TJunc peak = +125°C
    (Contact supplier for higher temperature)
E523.06 (*SoC)
Field-Oriented DC Motor Controller with 16 Bit CPU
  • LIN 2.x (1.3 comp.),
    SAE-J2602 or
    PWM bidirectional
  • SPI for configuration
  • LIN Flash update
  • JTAG

7V to 28V (5V to 42V)

6x ±400mA

≈1.5kW (external FETs)
≈1.3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN48L7
  • 16bit/48 MHzCPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack software update via LIN
  • Charge Pump Driver included
  • TJunc peak = +125°C
    (Contact supplier for higher temperature)
E523.26 (*SoC)
DC Motor Driver with 16kB Flash
  • LIN 2.x (1.3) or
    SAE-J2602
  • SPI for configuration

5V to 20V
(5V to 40V)

1 channel

≈1.5kW
(external FETs)
≈1.3W
(direct drive)

8Ω (HS)
8Ω (LS)

QFN32L6
  • Includes μC, memory, interfaces, high side gate driver, supply and measurement functions
  • TJunc peak = +150°C
E523.62 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD

  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 600mA/ch

≈9W

1.6Ω (HS)
3.0Ω (LS)

TSSOP16-EP
  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 
E523.63 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD

  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 1000mA/ch

≈15W

0,6Ω (HS)
1,0Ω (LS)

TSSOP16-EP
  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 
E910.72 (*Driver IC)
6x Half-Bridge DC Motor with sensorless positioning
  • SPI™ for configuration

6V to 19V (40V)

-

≈7W
(1 Motor Mode)

1.25Ω

QFN32L5
  • Sensorless motor positioning
  • 3 independent pulse detectors
  • Excellent positioning performance
  • Drives 3 or 5 DC actuators
  • TJunc peak = +150°C

BLDC Motor BLDC Motor Controller

Part-No. / Function Interface VSUPPLY IPEAK P(Motor) peak RDSON Package Comment
E523.05 (*SoC)
BLDC Motor Controller with 16bit CPU (LIN/PWM Interface)
  • LIN 2.x (1.3 comp.),
    SAE-J2602 or
    PWM bidirectional
  • SPI for expansion
  • LIN Flash update
  • JTAG

7V to 28V (5V to 42V)

6 channel

≈1.5kW (external FETs)
≈3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN48L7
  • For new designs E523.06 is recommended
  • 16bit / 48 MHzCPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack, software update via LIN
  • Software support on request
  • TJunc peak = +125°C (contact supplier for higher temperature)
E523.06 (*SoC)
Field-Oriented BLDC Motor Controller with 16 Bit CPU
  • LIN 2.x (1.3 comp.),
    SAE-J2602 or
    PWM bidirectional
  • SPI for expansion
  • LIN Flash update
  • JTAG

7V to 28V (5V to 42V)

6 channel

≈1.5kW (external FETs)
≈3W (direct drive)

8Ω (HS)
4Ω (LS)

QFN48L7
LQFP48L7EP
  • 16bit / 48 MHzCPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack, software update via LIN
  • Software support on request
  • TJunc peak = +125°C (contact supplier for higher temperature)
  • Plug & Play:
    Demosoftware for
    - sensorless HVAC fan,
      engine cooling fan
    - field oriented control (FOC)
      for pumps
E523.52 (*SoC)
72V Brushless Motor Gate Driver with 16bit CPU
  • LIN Interface with external LIN transceiver
  • PWM Interface with external components
  • SPI for user expansion
  • LIN Flash update
  • JTAG

12V to 72V (7V to 76V)

6 channel

≈1.5kW (external FETs)

10Ω (HS)
5Ω (LS)

QFN36L7
  • Usable for 24/48V automotive Board Net
  • 16bit/48 MHz CPU assisted by 2 powerful co-processors
  • Library ROM for LIN-stack software update via LIN (software support on request)
  • TJunc peak = +150°C
E523.62 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD

  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 600mA/ch

≈9W

1.6Ω (HS)
3.0Ω (LS)

TSSOP16-EP
  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 
E523.63 (*SoC)
Fully Integrated Motor Controller with 4 Half Bridges (under development)
  • LIN 2.2 autobaud interface and auto-addressing
    (compliant to LIN 2.0 and 1.3 and SAE-J2602-2),
    LIN 2.2 SNPD

  • User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF

7-18V
(5.5V-28V limited; 40V load dump)

4ch with 1000mA/ch

≈15W

0,6Ω (HS)
1,0Ω (LS)

TSSOP16-EP
  • Universal Controller to support BLDC, 
    Stepper and Brushed DC Motors
  • 40MHz ARM® Cortex®-M23 with 64kB Flash
  • SysROM including 
    Bootloader and LIN Stack
  • MotCoS ready 
Cookie-Popup anzeigen