SPI Stepper Driver | E523.39 (*Plug & Play) - HVAC Flaps - Elmos Semiconductor SE

Motor Control Stepper Motor

Part-No. / Function	Interface	Output	V_SUPPLY	I_PEAK	P(Motor) peak	RDS_ON	Package	Comment
E520.01 (*Driver IC) 12x Low-Side for 3 Stepper Motors with Stall Detection	SPI-compatible (3.3/5V)	12 channel	3V to 25V (42V)		≈12x 8.75W	1.5Ω	QFN32L5	Stall detection for stepper motors (E520.01) suitable for Full Step, Half Step, Wave Drive 245Hz LED mode 25kHz relay mode 25kHz linear PWM T_Junc peak = +150°C
E520.02 (*Driver IC) 12x Low-Side for 3 Stepper Motors	SPI-compatible (3.3/5V)	12 channel	3V to 25V (42V)		≈12x 8.75W	1.5Ω	QFN32L5	245Hz LED mode 25kHz relay mode 25kHz linear PWM T_Junc peak = +150°C
E520.03 (*Driver IC) 8x Low-Side for 2 Stepper Motors with Stall Detection	SPI-compatible (3.3/5V)	8 channel	3V to 25V (42V)		≈8x 8.75W	1.5Ω	QFN32L5 SOIC20	Stall detection for stepper motors suitable for Full Step, Half Step, Wave Drive 245Hz LED mode 25kHz relay mode 25kHz linear PWM T_Junc peak = +150°C
E523.30 (*SoC) Power Stepper Controller with Stall Detection and Auto Addressing (LIN/PWM Interface)	LIN 2.x (1.3 comp.) or SAE-J2602 or PWM Interface Optional LIN Auto-Addressing (SNPD) only E523.30 or LIN Flash update JTAG	2 channel	5.5V to 20V (42V)		≈ 25W	550mΩ(HS) 450mΩ(LS)	QFN32L6	Current chopper motor control Supply and read-out of up to 3 sensors Embedded 8bit µC 8k FLASH T_Junc peak = +170°C
E523.39 (*Plug & Play) SPI Stepper Driver	SPI-compatible (3.3/5V)	2 channel	5V to 28V (42V)		40W	0.5Ω (HS) 0.5Ω (LS)	QFN20L5 QFN32L6	Stall-Detection / analysis / position correction Sensitive Fail-Current-Detection Over modulation with customized waveforms Supporting Adaptive-Holding-Torque Supporting Adaptive-Run-Current T_Junc peak = +170°C
E523.62 (*SoC) Fully Integrated Motor Controller with 4 Half Bridges (under development)	LIN 2.2 autobaud interface and auto-addressing (compliant to LIN 2.0 and 1.3 and SAE-J2602-2), LIN 2.2 SNPD User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF		7-18V (5.5V-28V limited; 40V load dump)	4ch with 600mA/ch	≈9W	1.6Ω (HS) 3.0Ω (LS)	TSSOP16-EP	Universal Controller to support BLDC, Stepper and Brushed DC Motors 40MHz ARM® Cortex®-M23 with 64kB Flash SysROM including Bootloader and LIN Stack MotCoS ready
E523.63 (*SoC) Fully Integrated Motor Controller with 4 Half Bridges (under development)	LIN 2.2 autobaud interface and auto-addressing (compliant to LIN 2.0 and 1.3 and SAE-J2602-2), LIN 2.2 SNPD User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF		7-18V (5.5V-28V limited; 40V load dump)	4ch with 1000mA/ch	≈15W	0,6Ω (HS) 1,0Ω (LS)	TSSOP16-EP	Universal Controller to support BLDC, Stepper and Brushed DC Motors 40MHz ARM® Cortex®-M23 with 64kB Flash SysROM including Bootloader and LIN Stack MotCoS ready

BLDC Motor BLDC Motor Driver

Part-No. / Function	Interface	V_SUPPLY	I_PEAK	P(Motor) peak	RDS_ON	Package	Comment
E523.01 (*SBC) B6 Bridge FET Driver (LIN/PWM Interface)	LIN 2.x (1.3 comp.), SAE-J2602(only E523.01) or PWM bidirectional LIN Flash update	7V to 28V (5V to 42V)	6 channel	≈1.5kW (external FETs) ≈3W (direct drive)	8Ω (HS) 4Ω (LS)	QFN44L7 QSOP44	Voltage Regulator (3.3V/5V) selectable Precise deadtime generation Watchdog/Diagnostics T_Junc peak = +170°C Demo software on request (sensorless sinus)
E523.10 (*SoC) BLDC-Motor Driver with Cold-Crank Capability	PWM bidirectional SPI for configuration	7V to 28V (4.5V to 42V)	6 channel	≈1.5kW (external FETs) ≈3W (direct drive)	8Ω (HS) 4Ω (LS)	QFN44L7	Voltage Regulator (3.3V/5V) selectable Precise deadtime generation Watchdog/Diagnostics T_Junc peak = +170°C

Motor Control DC Motor

Part-No. / Function	Interface	V_SUPPLY	I_PEAK	P(Motor) max	RDS_ON	Package	Comment
E523.05 (SoC / Plug & Play) DC 2x Half-Bridge Controller with 16bit CPU (LIN / PWM Interface)	LIN 2.x (1.3 comp.), SAE-J2602 or PWM bidirectional SPI for configuration LIN Flash update JTAG	7V to 28V (5V to 42V)	6 channel	≈1.5kW (external FETs) ≈3W (direct drive)	8Ω (HS) 4Ω (LS)	QFN48L7	16bit/48 MHzCPU assisted by 2 powerful co-processors Library ROM for LIN-stack software update via LIN Charge Pump Driver included T_Junc peak = +125°C (Contact supplier for higher temperature)
E523.06 (*SoC) Field-Oriented DC Motor Controller with 16 Bit CPU	LIN 2.x (1.3 comp.), SAE-J2602 or PWM bidirectional SPI for configuration LIN Flash update JTAG	7V to 28V (5V to 42V)	6x ±400mA	≈1.5kW (external FETs) ≈1.3W (direct drive)	8Ω (HS) 4Ω (LS)	QFN48L7	16bit/48 MHzCPU assisted by 2 powerful co-processors Library ROM for LIN-stack software update via LIN Charge Pump Driver included T_Junc peak = +125°C (Contact supplier for higher temperature)
E523.26 (*SoC) DC Motor Driver with 16kB Flash	LIN 2.x (1.3) or SAE-J2602 SPI for configuration	5V to 20V (5V to 40V)	1 channel	≈1.5kW (external FETs) ≈1.3W (direct drive)	8Ω (HS) 8Ω (LS)	QFN32L6	Includes μC, memory, interfaces, high side gate driver, supply and measurement functions T_Junc peak = +150°C
E523.62 (*SoC) Fully Integrated Motor Controller with 4 Half Bridges (under development)	LIN 2.2 autobaud interface and auto-addressing (compliant to LIN 2.0 and 1.3 and SAE-J2602-2), LIN 2.2 SNPD User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF	7-18V (5.5V-28V limited; 40V load dump)	4ch with 600mA/ch	≈9W	1.6Ω (HS) 3.0Ω (LS)	TSSOP16-EP	Universal Controller to support BLDC, Stepper and Brushed DC Motors 40MHz ARM® Cortex®-M23 with 64kB Flash SysROM including Bootloader and LIN Stack MotCoS ready
E523.63 (*SoC) Fully Integrated Motor Controller with 4 Half Bridges (under development)	LIN 2.2 autobaud interface and auto-addressing (compliant to LIN 2.0 and 1.3 and SAE-J2602-2), LIN 2.2 SNPD User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF	7-18V (5.5V-28V limited; 40V load dump)	4ch with 1000mA/ch	≈15W	0,6Ω (HS) 1,0Ω (LS)	TSSOP16-EP	Universal Controller to support BLDC, Stepper and Brushed DC Motors 40MHz ARM® Cortex®-M23 with 64kB Flash SysROM including Bootloader and LIN Stack MotCoS ready
E910.72 (*Driver IC) 6x Half-Bridge DC Motor with sensorless positioning	SPI™ for configuration	6V to 19V (40V)	-	≈7W (1 Motor Mode)	1.25Ω	QFN32L5	Sensorless motor positioning 3 independent pulse detectors Excellent positioning performance Drives 3 or 5 DC actuators T_Junc peak = +150°C

BLDC Motor BLDC Motor Controller

Part-No. / Function	Interface	V_SUPPLY	I_PEAK	P(Motor) peak	RDS_ON	Package	Comment
E523.05 (*SoC) BLDC Motor Controller with 16bit CPU (LIN/PWM Interface)	LIN 2.x (1.3 comp.), SAE-J2602 or PWM bidirectional SPI for expansion LIN Flash update JTAG	7V to 28V (5V to 42V)	6 channel	≈1.5kW (external FETs) ≈3W (direct drive)	8Ω (HS) 4Ω (LS)	QFN48L7	For new designs E523.06 is recommended 16bit / 48 MHzCPU assisted by 2 powerful co-processors Library ROM for LIN-stack, software update via LIN Software support on request T_Junc peak = +125°C (contact supplier for higher temperature)
E523.06 (*SoC) Field-Oriented BLDC Motor Controller with 16 Bit CPU	LIN 2.x (1.3 comp.), SAE-J2602 or PWM bidirectional SPI for expansion LIN Flash update JTAG	7V to 28V (5V to 42V)	6 channel	≈1.5kW (external FETs) ≈3W (direct drive)	8Ω (HS) 4Ω (LS)	QFN48L7 LQFP48L7EP	16bit / 48 MHzCPU assisted by 2 powerful co-processors Library ROM for LIN-stack, software update via LIN Software support on request T_Junc peak = +125°C (contact supplier for higher temperature) Plug & Play: Demosoftware for - sensorless HVAC fan, engine cooling fan - field oriented control (FOC) for pumps
E523.52 (*SoC) 72V Brushless Motor Gate Driver with 16bit CPU	LIN Interface with external LIN transceiver PWM Interface with external components SPI for user expansion LIN Flash update JTAG	12V to 72V (7V to 76V)	6 channel	≈1.5kW (external FETs)	10Ω (HS) 5Ω (LS)	QFN36L7	Usable for 24/48V automotive Board Net 16bit/48 MHz CPU assisted by 2 powerful co-processors Library ROM for LIN-stack software update via LIN (software support on request) T_Junc peak = +150°C
E523.62 (*SoC) Fully Integrated Motor Controller with 4 Half Bridges (under development)	LIN 2.2 autobaud interface and auto-addressing (compliant to LIN 2.0 and 1.3 and SAE-J2602-2), LIN 2.2 SNPD User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF	7-18V (5.5V-28V limited; 40V load dump)	4ch with 600mA/ch	≈9W	1.6Ω (HS) 3.0Ω (LS)	TSSOP16-EP	Universal Controller to support BLDC, Stepper and Brushed DC Motors 40MHz ARM® Cortex®-M23 with 64kB Flash SysROM including Bootloader and LIN Stack MotCoS ready
E523.63 (*SoC) Fully Integrated Motor Controller with 4 Half Bridges (under development)	LIN 2.2 autobaud interface and auto-addressing (compliant to LIN 2.0 and 1.3 and SAE-J2602-2), LIN 2.2 SNPD User-configurable GPIOs including SPI,SEND, analog input and ARM-SWD IF	7-18V (5.5V-28V limited; 40V load dump)	4ch with 1000mA/ch	≈15W	0,6Ω (HS) 1,0Ω (LS)	TSSOP16-EP	Universal Controller to support BLDC, Stepper and Brushed DC Motors 40MHz ARM® Cortex®-M23 with 64kB Flash SysROM including Bootloader and LIN Stack MotCoS ready

Cookie settings

Our website uses technically necessary cookies, which must be set so that this website can be displayed correctly. In addition, we use statistics cookies to track the success of this website. You can edit the cookie settings at any time by clicking on the "Show cookie popup" button (usually on the bottom left or in the footer). If you no longer wish to consent to cookies for statistics, deactivate the checkboxes. For more information, please see our privacy policy.

Further details on the cookies used by us or by third parties on our website can be found here.

Required Statistics

	Title	Provider	Reason	Validity period	Names(s) of cookie(s)	Cookie domains
Required
	__cfduid	SiteSearch 360	Used by content delivery network Cloudflare to identify trusted web traffic.	1 Jahr	__cfduid	sitesearch360.com
	SiteSearch 360	SiteSearch 360	Is used for the search function of the website	1 Day	ssi--sessionId,ssi--lastInteraction	www.elmos.com
	HackShield EU-Cookie Opt-in	Elmos Semiconductor SE	Saves the cookie banner settings.	1 Year	hst3_cookieconsent	www.elmos.com
Statistics
	Matomo (Piwik)	Matomo (Piwik)	Visitor statistics for website optimization, bug analysis, cyber security pk_id – 13 months (used to store a few details about the user such as the unique visitor ID) _pk_ref – 6 months (used to store the attribution information, the referrer initially used to visit the website) _pk_ses, _pk_cvar, _pk_hsr – 30 minutes (short lived cookies used to temporarily store data for the visit) _pk_testcookie is created and should be then directly deleted (used to check whether the visitor’s browser supports cookies)	up to 13 months	_pk_ref, _pk_cvar, _pk_id, _pk_ses, _pk_hsr, _pk_testcookie, MATOMO_SESSID	www.elmos.com, kundenbereich.plehn-media.de